Reloading is a popular hobby in Canada!! Reloading is the process of making duplicate ammunition from previously fired brass. For professionals and gun owners who have limited budgets reloading can be a viable option. Reloading successfully is the greatest reward. You can keep shooting without breaking the bank 🔫 ️ !
Reloading: An Overview
To understand reloading, one needs to become familiarized with the components required and what processes are involved. The basics of reloading are fairly straightforward and the following is a brief rundown of the components and stages:
-Brass: This is the once fired empty case that is the foundation of reloading ️. It can be bought from a distributor (preferred) or collected from the range. It must be protected from moisture, damage, and most importantly, dirt.
-Primers: These are small cups, usually filled with a flammable compound, that when fired, ignite the powder, and propel the projectile forward ️. Primers are usually sold in boxes of 100 or 1,000, and should be stored in an airtight container, away from any other sources of ignition 💯. The type of primer used will depend on the type of powder and the firearm used.
-Powder: The type of powder chosen will be dependent on the gauge and type of firearm used, as well as the type of projectile being loaded 🔛. Powder should also be stored in an airtight container and out of reach of children .
-Projectiles: The bullet of choice must also be chosen according to the gauge and type of firearm used. The weight and type of projectile used will affect the speed of the round the trajectory and penetration of the round .
-Die Sets: Die sets enable the reloader to resize the brass deprime it and expand the neck before the round is loaded. The type of die set used will depend on the caliber and type of round being loaded 🔛.
-Press: The press is the device used to resize the brass, deprime, expand the neck, and seat the projectile. The type of press used will depend on the size of the ammo being loaded, as well as the budget of the reloader.
Once the reloader is familiar with the basics of reloading, the following stages can be applied to begin loading new rounds 🆕.
Loading New Rounds
Step 1: Cleaning the brass – Depending on the source of brass, it will usually be covered in residue, and dirt 🔛 🆕. The reloader should use a tumbler or media to clean the brass, with brass polish to remove any stubborn residue ️.
Step 2: Resizing – Once the primer has been removed and the case is clean, the reloader can use the dies to resize the brass back to factory specs. This is an important step to ensure the firearm’s chamber accepts the reloaded round.
Step 3: Priming – The primers should then be installed into the primed brass, making sure that the primer is seated in the pocket at the correct depth . This is very important to ensure the primer fires when the round is fired .
Step 4: Powder – Once the powder is chosen, the reloader should use a powder dispenser to measure the correct amount into the case ️. This will depend on the type of powder and the firearm used but it is important to note that too much powder can cause excess pressure and damage to the firearm.
Step 5: Seating the Projectile – The projectile should then be seated into the case, using the die set . This is an important step to ensure the projectile is not seated too-deep or too shallow, as this can cause a misfire or inaccuracy when the round is fired ️.
Step 6: Crimp – The last step is to crimp the round. This is important to ensure the projectile does not move when the firearm is fired.
Reloading Supplies in Canada
Reloading supplies in Canada can be found in most gun shops, as well as online via Canadian suppliers. The key to successful reloading is finding the right equipment for the job 🔑. If the reloader is starting out, it is recommended to try out some used equipment first, to ensure the reloader is comfortable with the reloading process.
The following is a brief rundown of the different types of reloading supplies in Canada:
-Brass: Brass can be purchased from distributors, but can also be collected from the range. The once fired brass should be checked for any damage or residue before reloading.
-Primers: Primers can be purchased in boxes of 100 or 1,000, and should be stored in an airtight container 💯. The type of primers used will depend on the type of powder and the firearm being used.
-Powders: Powders come in a variety of forms and can be chosen according to the type of firearm and projectile being loaded. Powders should be stored in an airtight container and out of reach of children .
-Projectiles: Projectiles come in a variety of weights and types ️. The type chosen should be chosen to suit the gauge and type of firearm used, as well as the desired results the reloader wants to achieve .
-Die Sets: Die sets enable the reloader to resize the brass deprime it and expand the neck before the round is loaded. The type of die set used will depend on the caliber and type of round being loaded 🔛.
-Presses: These are devices that resize brass, shrink necks, expand necks, and place projectiles. The size and budget of the reloader will determine the type of press that is used .
Conclusion
Reloading is a rewarding hobby that can save shooters money in the long run ️ 💰. It is important that reloaders are familiar with the components and processes involved before they begin to load their own ammunition. Supplies can be found in most gun shops in Canada, as well as online 🔫. With the right tools and knowledge, one can safely, and successfully reload their own ammunition with ease 1️⃣. !! .
️ 1️⃣ 🇨🇦 🔫 🏦 💺 🔙 🔛 🍁 💰 🆕 🔑 💯 🏭
